1. The feeding and mixing machine should not be repaired and lubricated during operation.

2.定期在每個潤滑脂嘴上添加黃油，并在軸端密封處每4小時潤滑一次油，每周排水一次。

2. Regularly add grease to each grease fitting, lubricate the shaft end seal every 4 hours, and drain water once a week.

3.使用上料攪拌一體機后，根據需要在每個潤滑點添加必要的潤滑油（滾筒軸，滾筒，鋼絲繩和其他有效部件）。

3. After using the feeding and mixing machine, add necessary lubricating oil (drum shaft, drum, wire rope and other effective parts) at each lubricating point as required.

4.上料攪拌一體機減速機的齒輪和軸承使用齒輪旋轉將油濺入油箱內壁并流入軸承進行潤滑。變速箱的油位應保持在油量計的兩條線之間。油位過高或過低都會導致各部件溫度升高或潤滑不良，增加動力損失并導致機器運行不良。

4. The gears and bearings of the reducer of the feeding and mixing machine splash the oil into the inner wall of the oil tank and flow into the bearing for lubrication. The oil level of the gearbox should be maintained between the two lines of the oil gauge. If the oil level is too high or too low, the temperature of each part will rise or the lubrication will be poor, which will increase the power loss and lead to the poor operation of the machine.

5.自動送料攪拌機選用的潤滑油應具有一定的粘度和粘溫特性，低凝固點，良好的氧化穩定性，無機械雜質和水分，無腐蝕和耐磨材料。其質量指標應符合標準。

5. The lubricating oil selected by the automatic feeding mixer should have certain viscosity and viscosity temperature characteristics, low freezing point, good oxidation stability, no mechanical impurities and moisture, no corrosion and wear-resistant materials. The quality index should meet the national standard.

上料攪拌一體機用于潤滑，減少磨損，提高部件的使用壽命。但是，在添加潤滑油的過程中需要注意一些事項。新機器應在更初150小時和300小時內更換一次，以測試期間未完全清潔的污垢。工作時，請務必檢查油位，并及時添加。

The feeding and mixing machine is used for lubrication, reducing wear and improving the service life of components. However, in the process of adding lubricating oil, we need to pay attention to some matters. The new machine should be replaced once in the first 150 hours and 300 hours to remove dirt that was not completely cleaned during the test. When working, please check the oil level and add it in time.

上料攪拌一體機的配置和操作

Configuration and operation of feeding and mixing machine

上料攪拌一體機的主要相關結構是行走底盤，發動機，液力變矩器，雙驅動軸，進料裝置，進料斗，卸料斗，延伸卸料斗，框架，攪拌桶和攪拌均特別慢一點。機械，液壓系統，電子控制系統，自動供水系統等讓我們仔細看看。

The main related structures of the feeding and mixing machine are walking chassis, engine, hydraulic torque converter, double drive shaft, feeding device, feed hopper, discharge hopper, extended discharge hopper, frame, mixing drum and mixing are all slower. Machinery, hydraulic system, electronic control system, automatic water supply system, etc. Let's have a closer look.

1.進水系統可根據稱重設置實現自動進水。

1. The water inlet system can automatically feed water according to the weighing setting.

2.攪拌筒的旋轉由液壓馬達通過特殊的行星齒輪驅動，行星齒輪的輸出軸可以以恒定的角度擺動，以滿足在惡劣路況下攪拌筒的節拍。

2. The rotation of the mixing drum is driven by a hydraulic motor through a special planetary gear. The output shaft of the planetary gear can swing at a constant angle to meet the beat of the mixing drum under bad road conditions.

3.雙螺旋葉片設置在上料攪拌一體機的混合滾筒的內壁上，正向旋轉進料和混凝土攪拌，反向旋轉混凝土在螺旋葉片的向下壓力下從出口排出。

3. The double helix blade is set on the inner wall of the mixing drum of the feeding and mixing machine, and the concrete is rotated forward and mixed, and the concrete is discharged from the outlet under the downward pressure of the spiral blade.

4.供應干料，按設計比例自動供給斗臂，動臂油缸和計量料斗。

4. Supply dry materials, automatically supply the bucket arm, boom oil cylinder and metering hopper according to the design proportion.

5.液壓系統使用恒功率可變排量活塞泵來減少發動機功率損失。

5. Hydraulic system uses constant power variable displacement piston pump to reduce engine power loss.

6.行駛系統由發動機從變矩器和前后驅動軸驅動到前后軸。變矩器的使用減少了對發動機的影響并延長了發動機的壽命。

6. The driving system is driven from the torque converter and the front and rear drive shafts to the front and rear axles. The use of the torque converter reduces the impact on the engine and extends the life of the engine.