Proper lubrication of the chassis of cement mixer can reduce the wear of automobile parts and increase the service life of mixer parts. However, the following points should be paid attention to when implementing lubrication:

1、正常使用情況下，按攪拌車廠家的保養周期進行潤滑，環境惡劣情況下要適當縮短保養周期。

1. Under normal use, lubrication shall be carried out according to the maintenance period of the mixer manufacturer, and the maintenance period shall be appropriately shortened in case of severe environment.

2、要選用規定的潤滑油。代用油料須性能接近，主要技術指標須保證，并且用代用油應時常檢查，且縮短使用周期。

2. Select the specified lubricating oil. The performance of the substitute oil must be close, the main technical indexes must be guaranteed, and the substitute oil should be checked frequently, and the service cycle should be shortened.

3、更換發動機機油時，要在熱狀態時進行，以保證油能放盡。放油時應注意檢查機油顏色是否正常、機油有無異物，以便發現故障隱患。待油放盡后，放油螺栓上的異物，然后擰緊。

3. When changing the engine oil, it should be carried out in the hot state to ensure that the oil can be drained. Pay attention to check whether the oil color is normal and whether there is any foreign matter in the oil in order to find out the hidden trouble. After the oil is drained, the foreign matters on the drain bolt shall be tightened.

4、進行潤滑前，要清潔入口。潤滑后要清潔零件表面，以免沾上塵土和污物。

4. Clean the inlet before lubricating. Clean the surface of parts after lubrication to avoid dust and dirt.

紅巖杰獅四橋輕量化攪拌車

Hongyan Jieshi four bridge lightweight mixer

5、更換新機油濾芯，將新機油注入發動機到油尺上限。為防止在沒有潤滑油的情況下啟動發動機，應使高壓油泵處于斷油位置時按啟動按鈕，空轉一會兒后，再啟動發動機，并低速運轉。檢查機油濾清器有無滲漏，停機后，檢查并補充機油油面到油尺上。

5. Replace the oil filter element and fill the engine with new oil to the upper limit of the dipstick. To prevent starting the engine without lubricating oil, press the start button when the high-pressure oil pump is in the oil cut-off position. After idling for a while, start the engine again and run at a low speed. Check the oil filter for leakage. After shutdown, check and replenish the oil level to the dipstick.

6、換機油濾芯：更換機油時，機油濾清器要同時更換，在密封墊上涂上一層薄薄的油，并且緊固濾清器。

6. Change the oil filter element: when changing the oil, change the oil filter at the same time, apply a thin layer of oil on the gasket, and fasten the filter.

本文由水泥自上料攪拌車為您提供，我們的網站是：http://f3328.cn我們將以全心全意的熱情為您提供服務，歡迎您的訪問！

Our website is: http://f3328.cn and we will provide you with our wholehearted enthusiasm. Welcome to visit!