通常，在使用自上料攪拌輸送一體機的過程中，如果要改善設備的操作和使用并保持設備的良好性能，則需要對攪拌機進行適當?shù)木S護。但是，在維護過程中有一些注意事項。讓我們輕松地理解它。

Generally, in the process of using the self feeding mixing conveyor, if you want to improve the operation and use of the equipment and maintain the good performance of the equipment, you need to properly maintain the mixer. However, there are some precautions during maintenance. Let's understand it easily.

1.清潔機器時，只能擦拭電箱，不能沖洗電箱。

1. When cleaning the machine, only wipe the electric box, not flush the electric box.

2.要調節主軸密封圈密封套，有必要將泵芯和供油支架分開，然后擰緊三顆螺釘。擰緊螺釘后的標準配置：用8英寸可動手輕松拉動主軸的螺釘。

2. To adjust the sealing sleeve of the main shaft sealing ring, it is necessary to separate the pump core from the oil supply support, and then tighten the three screws. Standard configuration after tightening the screw: use 8 inches to easily pull the screw of the spindle.

3.在施工現場移動機器時，無論距離多遠，都必須先拔掉電源線。

3. When moving the machine at the construction site, no matter how far away it is, the power cord must be unplugged first.

4.機器運行時，必須關閉并鎖上電箱門，以防止灰塵和濕氣進入并損壞機器組件。

4. When the machine is running, the electric box door must be closed and locked to prevent dust and moisture from entering and damaging the machine components.

5.軸承座應在工作前后每天加油，并應經常檢查變速箱油。

5. The bearing pedestal shall be filled with oil every day before and after work, and the transmission oil shall be checked frequently.

6.每次清潔泵芯時，都需要添加少量硅油以防止?jié)櫥痛檀?。目的是防止轉子鐵芯生銹，并在下次順利啟動。

6. Each time the pump core is cleaned, a small amount of silicone oil needs to be added to prevent lubrication and puncture. The purpose is to prevent the rotor core from rusting and start smoothly next time.

由于自上料攪拌輸送一體機采用全液壓技術，因此有必要考慮液壓預見的質量，以了解所有液壓技術是否。由于該動力來自發動機，因此除了發動機的性能和質量外，還必須考慮汽車底盤的性能，承載能力和質量。為了嚴格執行維護，必須嚴格按照正確的操作流程進行車輛設備維護。

Since the all-in-one machine of self feeding, mixing and conveying adopts full hydraulic technology, it is necessary to consider the quality of hydraulic prediction to understand whether all hydraulic technologies are advanced. Since the power comes from the engine, in addition to the performance and quality of the engine, the performance, bearing capacity and quality of the automobile chassis must also be considered. In order to strictly carry out maintenance, vehicle equipment maintenance must be carried out in strict accordance with the correct operation process.