1、液壓系統壓力應符合使用說明書中的規定,不得隨意調整。液壓油的油質和油量應符合原定要求。
1. The pressure of the hydraulic system shall meet the requirements of the operation manual and shall not be adjusted at will. The quality and quantity of hydraulic oil should meet the original requirements.
2、水泥自動攪拌車裝料前,應先排凈拌筒內殘存的積水和雜物。在運輸過程中要不停的轉動,以防混凝土離析?;炷翑嚢柽\輸車到達工地和卸料之前,應先使拌筒全速以14—18轉/分轉動1—2分鐘,然后再進行反轉卸料。反轉之前,應使攪拌筒停穩不轉。
2. Before loading the concrete mixer, the residual water and debris in the mixing drum should be drained. Keep turning during transportation to prevent concrete segregation. Before arriving at the construction site and discharging, the concrete mixer truck should first rotate the mixing drum at a full speed of 14-18 rpm for 1-2 minutes, and then reverse discharging. Before reversing, the mixing drum should be stopped.
3、環境溫度高于+25攝氏度,從裝料、運輸、到卸料延續時間不得超過60分鐘,環境溫度低于+25攝氏度,上述時間不得超過90分鐘。
3. When the ambient temperature is higher than + 25 ℃, the time from loading, transportation to unloading shall not exceed 60 minutes; when the ambient temperature is lower than + 25 ℃, the above time shall not exceed 90 minutes.
4、冬期施工時,應切實做到:開機前檢查是否結冰;下班時認真排除拌筒內及供水系統內殘存積水,關閉水泵開關,將控制手柄置于“停止”位置。
4. During winter construction, it is necessary to check whether there is ice before starting up, carefully remove the residual water in the mixing drum and water supply system when off duty, turn off the water pump switch and put the control handle in the "stop" position.
5、在施工現場卸料完畢后,應立即用攪拌車隨帶的軟管沖洗進料斗、出料斗、卸料溜槽等處,粘附在車身各處的污泥及混凝土。在返回攪拌站的途中,應向攪拌筒內注150---200L水以清洗筒壁及葉片粘結的混凝土殘渣。
5. After unloading at the construction site, the feeding hopper, discharging hopper, discharging chute, etc. shall be washed immediately with the hose attached to the mixer truck to remove the sludge and concrete adhered to the vehicle body. On the way back to the mixing plant, 150-200l water should be injected into the mixing drum to clean the concrete residue bonded on the wall and blades of the drum.
6、每天工作結束后,司機應負責向攪拌筒內注入清水并高速(14—18轉/分)旋轉5—10分鐘,然后將水排去,以保證筒內清潔。用高壓水清洗攪拌筒各個部分時,應注意避開儀表及操縱桿等部位。壓力水噴嘴與車身油漆表面間的距離不得小于40厘米。
6. At the end of each day's work, the driver shall be responsible for injecting clean water into the mixing drum and rotating at high speed (14-18 RPM) for 5-10 minutes, and then discharging the water to ensure the cleanness of the drum. When using high-pressure water to clean each part of the mixing drum, attention should be paid to avoid the instrument and control rod. The distance between the pressure water nozzle and the body paint surface shall not be less than 40 cm.
7、攪拌筒內外積污及殘存的混凝土渣塊時,以及在機修人員進入筒內進行檢修和焊補作業時,需先關閉汽車發動機,使攪拌筒完全停止轉動。在機修人員進入筒內工作期間,必須保證拌筒內通風良好,空氣新鮮,無可然氣體及有害灰塵,氧氣供應充足(不得使用純氧)。在筒內使用電動工具操作時,操作人員必須有良好的絕緣保護。
7. When removing the dirt and residual concrete slag inside and outside the mixing drum, and when the maintenance personnel enter the drum for maintenance and welding repair, it is necessary to turn off the automobile engine to stop the mixing drum completely. During the working period, the maintenance personnel must ensure that the mixing cylinder is well ventilated, the air is fresh, there is no natural gas and harmful dust, and the oxygen supply is sufficient (pure oxygen is not allowed). When using electric tools in the cylinder, operators must have good insulation protection.
8、工作時,不得將手伸入旋轉的攪拌筒內,嚴禁將手伸入主卸料溜槽和加長卸料溜槽的連接部位,以免發生事故。
8. When working, do not put your hand into the rotating mixing drum, and do not put your hand into the connecting part of the main discharge chute and the extended discharge chute, so as to avoid accidents.
9、應定期檢查攪拌葉片磨損情況并及時進行修補和換新。
9. The abrasion of mixing blades should be checked regularly and repaired and renewed in time.
This article is provided for you by self loading mixer. Our website is: http://f3328.cn1 We will serve you wholeheartedly and warmly. Welcome to visit!
上一篇:小型水泥自動攪拌車運輸前檢測事項
下一篇:移動水泥自動攪拌車高溫維護