攪拌車一般用于將混凝土輸送到施工現場,房屋行業很熱,所以施工現場很忙,
攪拌車也是不停的,攪拌車液壓系統使用比較頻繁,很多司機反映攪拌車液壓系統溫度過高的現象?那么我該怎么處理這些問題呢?,我們需要知道是什么原因,這樣我們才能從根本上問題。
The mixer truck is generally used to transport concrete to the construction site. The housing industry is very hot, so the construction site is very busy. The Zhongke Jufeng mixer truck is also nonstop. The hydraulic system of the mixer truck is frequently used. Many drivers report that the temperature of the hydraulic system of the mixer truck is too high. Then how can I deal with these problems? First of all, we need to know what the reason is, so that we can Can solve the problem fundamentally.
廠家的技術人員告訴我們,造成液壓系統高溫的原因有5個:
The technicians of Zhongke Jufeng factory told us that there are five reasons for the high temperature of the hydraulic system:
1.嚴重泄漏的液壓系統,如果溢流閥設定壓力過高,過多的運動部件的磨損會使密封間隙增加,密封裝置損壞,油粘度太低,會導致泄漏增加,找到問題的原因。
1. For the hydraulic system with serious leakage, if the set pressure of the relief valve is too high, the wear of too many moving parts will increase the sealing clearance, damage the sealing device, and low oil viscosity, which will lead to the increase of leakage. Find out the reason to solve the problem.
2.液壓系統散熱不良。如油箱散熱面積不足,油箱油位過低。
2. Poor heat dissipation of hydraulic system. If the heat dissipation area of the oil tank is insufficient, the oil level of the oil tank is too low.
3.油的粘度太大,也會造成水力損失太大。
3. The viscosity of oil is too large, which will cause too much hydraulic loss.
4.卸荷回路的液壓系統,當水泥自動攪拌車系統卸載循環工作不良或沒有卸貨,混合器系統不需要強調,和石油仍在閥設置溢流罐的工作壓力下,或在卸貨壓力高的意思是回油,這個時候應該仔細檢查正常卸載電路工作系統,如果卸油方式被污垢,或電氣系統故障,由于電磁閥卸荷效果不能工作,應及時采取措施加以排除。
4. For the hydraulic system of the unloading circuit, when the unloading cycle of the concrete mixer system is poor or there is no unloading, the mixer system does not need to emphasize, and the oil is still under the working pressure of the overflow tank set by the safety valve, or the unloading pressure is high, which means oil return. At this time, the normal unloading circuit working system should be carefully checked, if the unloading mode is dirty, or the electrical system fails, As the unloading effect of the solenoid valve cannot work, measures should be taken to eliminate it in time.
5.如果上述故障排除后,液壓系統仍然存在高溫的問題,有可能是由于直接影響油溫升高速度控制方法,系統壓力、液壓缸、泵和電機的效率,額定流量的直徑的各種閥門、管道、油箱體積,在液壓和卸貨的問題處理不當造成的,應該結合實際,具體分析,得出正確的結論。
5. If the problem of high temperature still exists in the hydraulic system after the above troubleshooting, it may be caused by the improper handling of various valves, pipes and tank volumes that directly affect the speed control method of oil temperature rise, the system pressure, the efficiency of hydraulic cylinders, pumps and motors, the diameter of rated flow, and the problems of hydraulic pressure and unloading, it should be combined with the actual situation and analyzed in detail to draw correct conclusions.
總之,無論發生什么樣的混車故障,一定要冷靜,找到故障的根源,這樣才能迅速問題!
In a word, no matter what kind of mixed vehicle fault happens, we must be calm and find the root cause of the fault first, so as to solve the problem quickly!
以上是廠家為大家介紹的相關內容,想要了解更多內容,歡迎訪問網站:http://f3328.cn
The above is the relevant content introduced by Zhongke Jufeng factory. To learn more, please visit the website: http://f3328.cn
上一篇:中科自上料水泥攪拌車對使用物料的要求
下一篇:水泥自動攪拌車攪拌筒一般采用什么材料