一、罐體傾斜角度小,低,行駛及轉動穩定
1、 The tank has small inclination angle, low center of gravity and stable driving and rotation
罐體采用德國施維英工藝,根據不同底盤做特殊優化,采用專用工裝,保證了罐體傾斜角度小,更低,不易側翻。減少焊接面積,大大增加了攪拌罐的強度。鋼材采用的等離子切割技術,保證生產效率的同時,減小因熱力而使鋼材產生形變的誤差。
The tank body adopts German schweining process, and is specially optimized according to different chassis. Special tooling is adopted to ensure that the tank body has small inclination angle, lower center of gravity and is not easy to roll over. The welding area is reduced and the strength of the mixing tank is greatly increased. The steel adopts advanced plasma cutting technology to ensure the production efficiency and reduce the deformation error of steel due to heat.
二、攪拌、進出料性能優越
2、 Excellent mixing, feeding and discharging performance
封頭、筒體、葉片均采用Q345合金鋼制作,耐磨和抗屈服強度好,使用壽命長。葉片采用雙對數,阿基米德螺旋線,攪拌性能優越,進料速度大于2.7立方每分鐘,出料速度大于1.8立方每分鐘,殘余率低。
The head, cylinder and blade are made of Q345 alloy steel, with good wear resistance and yield strength and long service life. The blade adopts double logarithm, Archimedes helix, excellent mixing performance, feeding speed greater than 2.7 cubic per minute, discharging speed greater than 1.8 cubic per minute, low residual rate.
三、副車架抗扭能力強
3、 The subframe has strong torsion resistance
副車架的縱、橫梁采用16Mn材質的矩形管制作,一體成型,無拼焊,關鍵受力部位應用斜拉結構,使車架具有較強的抗扭轉,抗撕裂能力。副車架與底盤連接結構可靠,減輕上裝部分的扭轉對底盤的影響,從結構上延長了底盤的使用壽命。
The longitudinal and cross beams of the subframe are made of 16Mn rectangular tubes, which are formed in one piece without welding. The key stressed parts are of cable-stayed structure, so that the frame has strong torsion resistance and tear resistance. The connection structure between the subframe and the chassis is reliable, which reduces the impact of the torsion of the upper part on the chassis and extends the service life of the chassis.
四、進出料系統
4、 Feeding and discharging system
進料斗空間大,設計角度合理,是進料速度加快,不易發生堵料和溢出現象;溜槽能進行180度旋轉,帶限位裝置,上下左右均可調整,其上設有鎖止裝置,在車輛行駛過程中將其固定鎖緊,以確保行駛可靠。
The feeding hopper has large space and reasonable design angle, so the feeding speed is accelerated, and it is not easy to block and overflow. The chute can rotate 180 degrees, with a limiting device, which can be adjusted up, down, left and right. It is equipped with a locking device, which can be fixed and locked in the process of vehicle driving to ensure safe and reliable driving.
五、液壓系統
5、 Hydraulic system
液壓傳動系統采用流體動力領域的全球知名企業:ZF、PMP、Bonfiglioli、Rexroth、Eaton、Danfoss等,讓高品質的可靠性得以傳承。
The hydraulic transmission system adopts the world famous brands in the field of fluid power: ZF, PMP, Bonfiglioli, Rexroth, Eaton, Danfoss, etc., so as to inherit the high-quality reliability.
六、操縱系統
6、 Control system
操縱系統采用定位準確、控制可靠的桿式控制系統,控制點在駕駛室內、車尾兩側共三處??刂葡到y(tǒng)結構緊湊、操作靈活、控制可靠。
The control system adopts the rod control system with accurate positioning and reliable control. The control points are in the cab and on both sides of the rear of the car. The control system has compact structure, flexible operation and reliable control.
上一篇:鏟挖一體機磨合期應該注意什么?
下一篇:小型攪拌車殘?jiān)趺催M(jìn)行處理?