自動攪拌車的正確操作方法可以歸納為：一輕、二穩、三離、四勤、五協調、六嚴禁。下面小編就來為您詳細講講其中的內容點吧。

The correct operation methods of the automatic mixer can be summarized as follows: one light, two stable, three separated, four diligent, five coordinated and six forbidden. Let's talk about the content points in detail.

一輕：

One light:

在自動攪拌車作業時腳跟緊抵駕駛室地板，腳板和油門踏板保持平行，輕緩地下壓加油踏板。

During the operation of the automatic mixer truck, the heel is firmly against the cab floor, the foot plate is parallel to the accelerator pedal, and the refueling pedal is gently pressed.

二穩：

Bistable:

自動攪拌車在作業中，油門始終要穩住。一般作業狀態下，油門開度在70%左右為宜。

During the operation of the automatic mixer, the accelerator should always be stable. In general operation state, the throttle opening should be about 70%.

三離：

Three Departures:

在自動攪拌車作業時，腳板應和制動踏板分離開，平放到駕駛室地板上，決不能踩在制動踏板上。自動攪拌車常常在凹凸不平的工地作業，如果腳總是踩在制動踏板上，機身上下竄動會造成駕駛員不輕意地踩制動踏板。一般情況下，要用控制油門減速的辦法控制機況和換擋。這樣既避免了頻繁制動造成制動系統過熱，又為自動攪拌車快捷的提速帶來方便。

During the operation of the automatic mixer, the foot plate shall be separated from the brake pedal, and placed flat on the cab floor. Never step on the brake pedal. The automatic mixer often works on uneven construction sites. If the foot always steps on the brake pedal, the body will move up and down, causing the driver to step on the brake pedal carelessly. In general, the engine condition and gear shifting shall be controlled by controlling the throttle deceleration. This not only avoids overheating of the braking system caused by frequent braking, but also brings convenience for fast speed increase of the automatic mixer.

四勤：

Four attendance:

在自動攪拌車作業時，特別是在鏟挖作業時，應在油門穩定情況下，用循環扳動起升和轉斗操縱桿的方法使鏟斗鏟滿物料。起升和轉斗操縱杠的循環扳動就是所說的“勤”。這個過程非常重要，對耗油量的影響很大。

During the operation of the automatic mixer, especially during the shoveling operation, the bucket shall be filled with materials by cyclically pulling the lifting and bucket turning control levers under the condition that the accelerator is stable. The cyclic pulling of the lifting and turning lever is called "diligence". This process is very important and has a great impact on fuel consumption.

五協調：

V. Coordination:

協調就是起升和轉斗操縱杠有機的配合。自動攪拌車一般的鏟挖過程是將鏟斗平放在地面，平穩地駛向料堆。在鏟斗平行鏟往料堆遇阻力時，應遵循先起臂后收斗的原則。這樣可以有效地避免鏟斗底部受到阻力，從而能夠充分發揮大的掘起力。

Coordination is the organic cooperation between the lifting and bucket control rods. The general shovel digging process of automatic mixer truck is to place the bucket flat on the ground and drive steadily to the material pile. When the bucket is parallel to the material pile and encounters resistance, the principle of lifting the boom first and then retracting the bucket shall be followed. This can effectively prevent the bucket bottom from being subjected to resistance, so as to give full play to the large digging force.

六嚴禁：

VI. Prohibitions:

是嚴禁輪胎打滑。其次是嚴禁后輪翹起。三是嚴禁撞擊料堆。

First of all, it is forbidden to slip the tires. Secondly, it is forbidden to tilt the rear wheel. Third, it is strictly prohibited to impact the material pile.

以上內容就是所說的自動攪拌車的正確操作方法的“六步歸納”！希望給你好的幫助，更多事項就來我們網站http://f3328.cn進行咨詢吧！

The above content is the "six step summary" of the correct operation method of the automatic mixer truck! I hope to give you some help. Please come to our website for more information http://f3328.cn Consult!